Ads by Google
1.production photo
2.Technical Data
| Technical Data | Unit | DBC145 |
| Passage width | mm | 550 |
| Throughput rate | p/m | 35 |
| Power supply | V(ac) | 220~240 |
| Operational voltage | V(dc) | 24 |
| Max power consumption | w | 32 |
| Frequency | hz | 50~60 |
| Prectection level | ip | 44 |
| Working temperature | -25~+70 | |
| Electro-magnetic drive | DC | |
| Dimension excluding bars | mm | 1300×280x980 |
| Net weight including bars | kg | 90 |
3.Metrial Processing
4.Pure Manual Welding
5.Pure Manual finishing
6.Fixed Acrylic
7.Machine Core
1).Machine core be fixed by tri-square tube holder .2).The shock absorber of machine core will reduce noice and impact .3). Metrail of all fixed screw are 304 stainless steel .
Notes:Lock arms and solenoids (Operation to be carried out with the power supply disconnected.):
—Grease the pins of the lock arms that slide on the solenoid shaft.
—Grease the solenoid shaft and spring, and do not grease the core of the solenoid
—check that the shaft/lock arm assembly moves freely.
8.Driver control board
1). The PCB board is developed by our company.2). The PCB board be processed by listed company .10.Testing
1). Check the wiring
When connected power debugging, please check the wiring diagram according to each parts of the line is connected
Note: protective earth wire of equipment must reliable grounding, otherwise don't allow debugging.
2). Function test
(1) Turnstile actually pick two way signal (come in and out ).
(2) if the installation has LED indicator light on the surface, if the control PCB board receive the legitimate signal , turnstile will have green arrows in the direction.
11.Package
12.Warnings
Before starting installation, you must pay attention to those notes
1.Before starting installation and operation or maintenance, cut off power supply.
2.The product must be earthed, and an earth leakage breaker is necessary on the power supply.
3.Do not change the original inside wiring.
4.Keep the automatic control (push-button , remote control , etc) out of the reach of children .The control system must be installed at a minimum height of 1.5mm the ground surface.
5.Never open the door or the cover of the cabinet when the machine is working .
13.Maintance
1) General indications
The tripod turnstile should be inspected and cleaned at regular intervals. If used in the subway or the light rail station, the inspection interval is recommended to be 6 months. The users are also encouraged to determine the interval according to their own situation.
To avoid the risk of electric shock, always ensure that the electrical power is disconnected before inspecting the mechanism.
2)Oil pressure of the damper
Operation should be carried out with the power supply disconnected:
--Check whether the damper oil spills;
--Check whether the force exerted by the spring is enough;
--The force exerted by the spring should match that exerted by the damper.
3)Upper positioning cam
Operation should be carried out with the power supply disconnected.
—Loosen the spring of the positioning lever.
—Check the guide way in the cam is clean and not excessively worn.
—Check some metal powder or the like sticks to the solenoid
—Check the guide pin of the positioning lever for excessive play.
—Check the magnetic strip is perfectly attached to the edge of the cam
4)Tripod
Operation should be carried out with the power supply disconnected.
Check tightness of the three securing the base plate to the mechanism shaft.
5) Emergency Drop Arm Device
Clean all dust from the arm detents, the arm drop lever and the relative solenoid. Do not lubricate these parts.
6)Cable and Connectors
Operation should be carried out with the power supply disconnected:
--Check that the wire connectors are firmly attached.
--Check that the terminals are fully tightened.
--Check that the insulation of the wires is in good condition and that no conductors are exposed.
14.Certification
15.FQA
Q:The Indicator lamp does not illuminate
A: Check the power supply and fuse
Q: Tripod permanently locked
A: Check the control board
Check the driving board.
Check the screws of the solenoid.
Q: The tripod jingles noisily when in operation.
A: Adjust the screws of buffer
Q: There is a hum when the tripod is in operation
A:Adjust the four screws of the solenoid to shorten the space.
16.Project Case
17.About us
Thank you very muck for your view ! Any question , that will be appreciated !
Tel:86-755-29010765
Fax:86-755-29164103
Mobile:86-0-18603063542
Stainless steel automatic smart tripod turnstile access control