Welcome to ECVERY
Nicbond high flexible EPS Board Adhesive
Nicbond high flexible EPS Board Adhesive
Supplier Info
[China Supplier]
Contact Person : Mr. Cao Jerry
Tel : 0086-20-87405183-806
Fax : 0086-20-87418670
Product Detail
Board Adhesive , A cement based high-strength inorganic board adhesive to stick EPS/XPS foam board

Board Adhesive

This product is a kind of high-strength inorganic adhesive specially developed in allusion to the case that common cement cannot be used as the light construction material, polystyrene board. It can substitute various organic cementing agents, lowering greatly the cost of construction. Features and benefits:1) Firm adhesion, excellent weather, so as to ensure the permanent firmness and adhesion of light construction materials2) Thin mortar technology adopted, with 1.5 - 3mm thick mortar, so as to lower the weight of building and the cold and heat bridge in the insulation layers3) With proper flexibility, able to compensate the temperature difference stress between the light construction materials and outer decoration paints due to difference from expansion coefficients4) Safe, innocuous, anti-mildew and flameproof5) A certain water resistanceApplication scope:1) The sticking between the polystyrene foam boards of outer insulated system of the external wall and the basic surface wall, and render of the protection layer of the foam board2) The sticking between such light boards as outer wall foam board decoration line, expanded perlite and so on with the basic surface3) The bricking mortar for air-added concrete brick, ash sand brick, powdered coal ash light brick, and gypsum bricklaying4) Sticking or bricking materials for foam board indoor partition, indoor and outdoor insulated boardSubstrate preparation:The substrate should be firm, even and free from grease or other loose substance.Instruction:1) Mix powder and water at ratio of 3.57:1 (i.e. 20kg powdered: 5.6kg water), then mix with an electrical mixer until it is equal, lump-free mixture is achieved; let it stand for 3 minutes, then re-stir and ready to use2) When it is used for the sticking between the polystyrene foam board, foam decoration line and the substrate notched trowel, use to spread the adhesive onto the substrate or the back of the foam, the foam decoration line, also point pasting method can be used; following application should be done more than 24 hours after this application3) When laying light bricks, the moving and adjustment shall be finished within 10 minutesSpecifications: 1) Tensile and bonding strength (with 20kg/m³ cement board):a) Normal strength: ≥0.7MPa b) Water resistance: ≥0.5MPa2) Tensile and bonding strength (with 20kg/m³ cement board):a) Normal strength: ≥0.1MPab) Water resistance: ≥0.1MPa 3) Operability time: 2.0±0.5hCoverage:For the evenness of the basic surface, use notched trowel method or pasting point method, approx. 3 ~ 4kg/sqmPrecautions:1) The product had better be used at 5°C - 40°C2) Before application, please confirm the vertically and evenness of the substrate3) If the surface of the adhesive cement is dry, please remove the surface crusting4) Do not add water to the cured adhesive and use it againShelf life:It can be put in the cool and dry place and can be saved for one year if not opened.Package:25kg/bag,Paper,PVC,Plastic three layers craft bags 

Nicbond high flexible EPS Board Adhesive

Ads by Google

About Us | Contact Us | Help | Terms & Conditions
Hot Products: A | B | C | D | E | F | G | H | I | J | K | L | M | N | O | P | Q | R | S | T | U | V | W | X | Y | Z | 0-9
Copyright Notice @ 2008-2013 ECVERY Limited and/or its subsidiaries and licensors. All rights reserved.