Ads by Google
JG602
Heavy duty-Hi load Adhesive for Chemical Anchoring
Description
JG602 is pure Epoxy based, Heavy duty-Hi load Adhesive for chemical anchoring in cartridge packaging.
Fields of Application
JG602 is used in;
• Chemical anchoring to concrete and brick walls,
• Repair and insulating of wide cracks,
• Bonding of various types of construction materials such as steel, concrete, brick to each other,
• Anchoring the rods and deformed bars to the concrete, stone or brick.
Benefits
• Rapid curing.
• Can be applied on damp surfaces on concrete.
• Pasty consistency, easy to apply and non-sag properties in over-head applications.
• Resists to chemicals.
Technical Data
product :JG602
variant : 360ml 5:1 dual action side by side cartridge
designation : heavy duty - hi load
material : pure epoxy ,styrene free
finish : gray on mixing
Application Procedure
Preparation of Anchor Holes
Anchor holes should be drilled 6mm wide than anchor bar’s diameter and drilled in designed depth. The holes should be cleaned by using a steel brush and air guns.Anchor bars should be cleaned from rust, dust and grease before anchoring.
Mixing
JG602 is packaged in ready to use cartridges. Fix the mixer nozzle to the front end of the resin cartridge. Fit the resin cartridge into the special dispenser gun and apply the correct number of trigger pulls until the colour of the resin comes out from the nozzle, changes.
Application Method
After removing the first resin came out from the nozzle apply the correct number of trigger pulls starting at the far side of the drilled hole. Insert the rebar or threaded rod into the hole. Install the anchor bar into the hole slowly by screwing and do not drive the bars. For threaded rods, apply the correct tightening torque only after the curing time specified for the resin.
Watchpoints• Do not use the resin first coming out from the nozzle.
• During the application the substrate and environment temperature should be between 5-35oC.• Do not apply the product on to the wet surfaces.
• Resinous materials’ pot life and curing times vary depending on the relative humidity, substrate and environment temperature. Reaction gets slow in low temperatures and it causes to extension on pot life and working time. On the other hand high temperatures speed up the reaction, which results to short pot life and working time. For full curing of material, both the substrate and environment temperature shouldn’t be under allowed application temperature.Cleaning
After the application all tools should be cleaned with a proper detergent or solvent such as thinner. YUANDA® JG360 can be cleaned with only mechanical abrasion after hardening.Packaging360 ml cartridge,40 Pcs/cartonStorageStore in original container in cool (+5oC - +25oC) and dry indoor conditions.Shelf life12 months under proper storage conditions after production date.Health and SafetyIt is dangerous to get close to the store areas with fire. The store must be well ventilated.
Work clothes, protective gloves, glasses and mask defined in Labour Laws must be used during the
application. Avoid from material to contact with skin and eyes. In case of contacting wash your skin with water and go to doctor immediately .Don’t bring any food and drink to the application area. Store the material away from the children.For further information Material Safety Data Sheets should be read.Disclaimer
This information and all further technical advice are based on our present knowledge and experience.YUANDA CO.LTD. is only responsible for product’s quality. The results, caused by wrong application and/or application methods and fields exception of technical advices on the application of the product in this technical data sheet, implies no liability or any other legal responsibility on YUANDA CO.,LTD
Cure Schedule
Base Material Temperature(°C) | Gelling time | Curing time |
-10°C~0°C | 2~8hours | 96~150hours |
0°C~+10°C | 1~2hours | 48~96hours |
+10°C~+25°C | 30~50mins | 24~48hours |
+25°C~+40°C | 20~30mins | 7~24hours |
>40°C | 12mins | 7 hours |
chemical mortar