Ads by Google
PVC coated Wire Mesh Fencing designs
Panel:
Using high quality Iron Rod as raw material, the welded panel, after galvanization, Powders Primer, and Powders top
coating; it can resist the corrosive and ultraviolet radiation very strongly.
1.The material of fence: Low carbon steel wire,AL-nlg alloy wire
2.Process: Steel rod-Strenthen wire-Cutting wire-Welding-Making curves-Surface Treatment-Packing
3.Surface Treatment: Electric galvanized then PVC coated/PVC paiting,Hot dip galvanized then PVC coated/PVC paiting,
Hot dip galvanized
Common Specifications
The Common Specification of Fence Panel | |
Wire diameter(mm) | 3mm—7mm,4mm,5mm is most popular |
Mesh/Opening(mm) | 50x100/50x150/50x200/60x100/60x200 75x150/75x200 as your request |
Length of panel(m) | 2m,2.5m or as your request |
Width of panel(m) | 1m,1.2m,1.5m,1.7m,1.8m,2m,2.5m, as your request |
Surface treatment | Hot-dipped Galvanized then PVC coating Hot-dipped Galvanized then PVC spraying Electric Galvanized then PVC coating Electric Galvanized then PVC spraying Hot-dipped Galvanized or Electric Galvanized |
Special specification can be produced as your request | |
Post:
The finished surface usually is Galvanized and Powder coating, or alternatively, with plastic caps or Roofing rainhat.According to different type. Such as buying additional 50cm pass panels height into earth or with bottom based and so on.
You can also make a choice according to your demand,because you have different styles.
Post Specifications
Post Style | Post Size |
Rectangle post | 40*60*1.2mm |
40*60*1.5mm | |
40*60*2mm | |
Square post | 60*60*1.2mm |
60*60*1.5mm | |
60*60*2mm | |
60*60*2.5mm | |
Peach post | 50*70mm |
70*100mm | |
Round post | 38mm*1.5mm |
40*1.5mm | |
42*1.5mm | |
Post Height | 2.0m,2.2m,2.4m as your request |
Clips: Plastic and Metal
Plastic clips
Metal clips
Galvanized Wire Mesh Fence
PVC coated Wire Mesh Fence
Post(Square,Rectangular,Round,Peach post):
How to install:
1.Check for underground utilities. This is important before you start digging holes for the fence posts because power,
fiber-optic or other cables may be present around the area of your fence.2.Mark your fence line. First you must decide where you wish to erect the terminal posts and gate, the bay area (the spacebetween the posts) and where you will install the plastic coated fence panels. To do this, run a roll of string along the imaginary perimeter of your fence, taking into account all fence corners.
3.Review your marked fence line. Before proceeding, check the fence line that you marked with string earlier to ensure that you have included markings for the fence gate and all corners. Make the necessary adjustments where required. When planning all bay areas, you may decide whether to set up an infill for privacy, or a series of rails.4.Mark the corner posts' locations. When you have reviewed your fence line and have made all necessary adjustments to your satisfaction, tie a string between the 4x4 corner post locations. Then finalize the measurements of your plastic coated fence panels accordingly.
5.Apply the measured panels. When you have measured the length of your panels, use a stake in the ground to apply them to the line posts' location. For example, for 6 foot panels set up 5 inch x 5 inch posts. Make sure the stakes are in physicalcontact with the layout string marker in order to keep the posts aligned. When doing so, keep in mind where the gates or other breaks in the fence are supposed to be.
6.Dig final holes for fence posts. Before you do so, you must decide what height you wish to have your fence and dig the holes to a suitable depth accordingly. A diameter of 10 inches is advised when digging your post holes. Now pour 6 inchesof gravel into each hole.
7.Fill all post holes with concrete. Follow instructions regarding the drying process and use of the concrete, before you do this.
8.Insert posts into concrete. Use a mallet or hammer to tap the posts down into position and ensure they are aligned.
Before the concrete dries, make any necessary adjustments.
9.Install plastic coated panels. Attach rail brackets to the fence posts, then, slot the panels into these brackets. Use bolts
and screws to fasten the panels to the hangers.
10.Install the gate. When doing this, ensure that the gate and fence are aligned at the bottom. Leave about 5/8 inch space
between the gate and the two posts on either side of it.
Packing system:
Shipping:
Hot sale in European countries PVC coated wire mesh fencing designs