Welcome to ECVERY
Fire Alarm Control Panel with 8 Zones PY-CK1008
Fire Alarm Control Panel with 8 Zones PY-CK1008
Supplier Info
[China Supplier]
Contact Person : Ms. Xiong Sunny
Tel : 86-755-82778062
Fax : 86-755-82778062
Product Detail
Fire Alarm Control Panel with 8 Zones;

Fire Alarm Control Panel with 8 Zones PY-CK1008

CK1000 Series Conventional Fire Alarm Control PanelGENERAL:The CK1000 Series Conventional Fire Alarm Control Panel is a 24 volt, four to sixteen-zone, Class B, ConventionalFire Alarm Control Panel. Designed exclusively to meetthe latest market requirements and future ULC codes, the highly cost-effective CK1000 Series can be used in a variety of low- to mid-sized applications.

FEATURES:? Four to Sixteen Style B (Class B) Initiating DeviceCircuits (IDCs). ?§C All zones accept two-wire smoke detectors and any normally-open contact devices.?§C Zones 1 - 16 configured as general alarm zones.? All circuits are power-limited and supervised, meeting the latest ULC requirements using fuseless technology.? Two built-in, Style Y (Class B) Notification Appliance(Signal) Circuits (NACs).? NACs may be programmed:?§C Silenceable.?§C Non-Silenceable.?§C Auto-Silence (program 5 to 20 minutes).? 1.25 amps of NAC power.? 3.0 amps of total system power.? Alarm, Trouble and Supervisory, relay output.? 24-volt operation.? Resettable four-wire smoke detector power @ 500 mA.? Non-resettable power @ 500 mA.? Integral battery charger capable of charging up to 18AH batteries (batteries over 4 AH require use of the external battery backbox, or ULC listed equivalent).? Disable/Enable control per IDC.? Reverse polarity protection.? Control buttons:?§C Mode?§C Test?§C ACK (Acknowledge) Alarm Silence?§C Reset? LED indicators:?§C AC Power(green & yellow LED)?§C Fire Alarm(red LED)?§C Trouble(yellow LED)?§C Supervisory(yellow LED)?§C Signal Silence(yellow LED)?§C Battery Power(green & yellow LED)?§C Zone Disable(yellow LED)?§C NAC Fault(yellow LED)?§C NAC Disable(yellow LED)?§C Zone Alarm(one for each zone) (red LED)?§C Zone Trouble(one for each zone) (yellow LED)?§C Earth Fault (on circuit board)?§C Battery Fault (on circuit board)?§C Charger Fault (on circuit board)

SPECIFIC ATIONSAC POWER ?§C 220 VAC, 50 Hz, 2.0 amps.?§C Wire size: minimum 14 AWG (2.0 mm2) with 600-volt in- sulation.? BATTERY?§C Sealed lead-acid batteries only.?§C Maximum charging circuit: 27.6VDC @ 0.8 amp for normal flat charge.?§C Maximum battery charger capacity: 18AH battery.NOTE: two 4AH batteries can be housed in the cabinet. Larger batteries require a separate battery box.? Total 24 V system power: 3.0 amps.? Notification appliance (signal) power: 2.5 amps.? Maximum current per NAC: 1.25 amps (expandable to 2.5amps).? Maximum battery charging capability: 18 AH.

Auxiliary Outputs? Resettable four-wire smoke detector power @ 500 mA.? Non-resettable power @ 500 mA.NOTE: Total current for auxiliary power outputs and two NACs must not exceed 3.0 amps. .? Integral Form-C Alarm, Trouble and Supervisory relays, rated at: 2.0 amps @ 30 VDC (resistive), 2.0 amps @ 30VAC (resistive).

CABINET AND MOUNTINGCABINET PHYSICAL DIMENSIONS: 40.0 cm high x 35.0 cm wide x 11.5 cm deep.CARTON PACKAGE DIMENSIONS: 48.0 cm high x 42.0 cm wide x 18.5 cm deep.CABINET NET WEIGH: 6.0 Kg. (without batteries).CABINET GROSS WEIGH: 6.6 Kg. (without batteries). MOUNTING: The cabinet mounts using two key slots at the top of the back and two additional 6.5mm diameter holes at the bottom.

Fire Alarm Control Panel with 8 Zones PY-CK1008

Related Products
Ads by Google

About Us | Contact Us | Help | Terms & Conditions
Hot Products: A | B | C | D | E | F | G | H | I | J | K | L | M | N | O | P | Q | R | S | T | U | V | W | X | Y | Z | 0-9
Copyright Notice @ 2008-2013 ECVERY Limited and/or its subsidiaries and licensors. All rights reserved.