Ads by Google
YAG Laser Tattoo Removal (L006)
Applications
The system gem-adjusting Q switch can effectively cure the mixed pigments by pigment precipitation of extraneous source with pathological pigment change of endogenous source, inclusive of erroneous dark eyebrow-embroidery, lip-embroidery, lip-soak, eye line-embroidery, lip-line, tattoo (inclusive of tattoo by extraneous wounds), pigment precipitation by sensitive source, freckle on female's face (male's), coffee spot, old age spot, black mole, and birthmark in black, blue, purple, brown, red and etc.1064nm laser can penetrate into deep layer of the skin,so it is easilly absorbed by blue,black and green color pigment;therefore,it is very suitable to treat the pigment disease in the dermal layer.For example,getting rid of tattoos,eyebrow,Ota's nevus and pigmented disease.532nm laser can penetrate into light layer of the skin;therefore,It is very easily absorbed by the brown,red and deep-brown color pigement.For example,eliminating freckles,pigment spots and other light-color tattoos.Treatment course for different illness case as follows:
| Functions | Treatment course required( cure times) | Treatment course interval |
| eyebrow-embroidery(eyeline grain) | 1 –2 times | 30-60 days |
| Eyebrow-embroidery (eyeline embroidery) | 1-3 times | 45-60 days |
| Lipline (red dyed lip) | 1-3 times | 15-45 days |
| Tattoo ( caused by extraneous wounds) | 1-4 times | 30-60 days |
| Freckle, old age spot | 1-4 times | 15-30 days |
| Birthmark, nevus | 3-7 times | 45-90 days |
1. Treatment for tattoo in eyebrowCustomer could not open eyes during treatment, operator should adjust energy according to depth of tattoo color, hold the handle and move it to treatment area slowly to make customer feel acceptable in mentally. Right now, the speed of flash could be set 3HZ, keep head of the handle a two-finger distance to treatment area, start treatment from head of eyebrow to end of eyebrow. It is needed to treat again in 5-10 minutes if the color of tattoo re-appear.2. Remove eye lineThe speed of flashes could be set 4-5HZ,adjust the energy of light to minimum energy, keep a one-finger distance between head of handle and treatment area. Operator should strictly protect customers’ eyes with panel for eyelid or medical pledget (panel for eyelid)of 1cm depth.Treatment should be started from down eye line, customer should deeply close eyes and keep eyeball up-sight inside. Operator should press the pledget (panel for eyelid) with forefinger and push up eyelid, peel down eyelid with middle finger to bare the eye line, treat it with flashes of 4-5Hz. Then, treat up eye line. Also customer should close eyes and keep eyeball down-sight inside. Operator should press the pledget (panel for eyelid) with middle finger and push eyelid down, push eyelid up with forefinger to bare the eye line, treat it with flashes of 4-5Hz.3. Remove lip lineThe speed of flashes could be set 5Hz,keep a 3/4 finger distance between head of handle and treatment area. It is better to remove black, coffee, deep, red and brown lip line with 1064nm head at first time and then, treat again with 532 nm head.Notice: All tattoos in lip should be treated in 6 months after making. OR removal treatment will fail. It should have 45-60 days interval to continue next treatment until remove all.4. Remove tattooThe speed of flashes could be set 3Hz/5Hz.It is better to use high energy for treatment until treatment area seeps a little blood. It should have 45-90 days interval to continue next treatment until remove all.5. Remove spot and nevusThe speed of flashes could be set 3Hz/5Hz.Keep 3-4 fingers distance between head of handle and treatment area. It is better to use high energy for treatment until treatment area seeps a little blood. It is advised to use 1064 nm head for normal spot and nevus treatment, but for deep color spot and nevus, it is better to use 532nm head for treatment. It should have a 15-30days interval to continue next treatment until remove all.6. Remove birthmarkThe speed of flashes could be set 3Hz/5Hz.It is better to use high energy for treatment until treatment area seeps a little blood. It is advised to use 1064nm head for birthmark treatment, but for red and deep color birthmark, it is better to use 532nm head for treatment. It should have 45-90 days interval to continue.Notice after treatmentTo avoid infection, please do not pencil the eyebrows (for eyebrows wash treatment), wash with water or be under the blazing sun. Smear anti-inflammation cream for 3-5 times every day. Do not eat stimulating food, such as spicy food, seafood, beef, and mutton. Also don't drink. The customer may feel itching of the treatment areas when it is scabby, but please don't peel off the scab by hand, otherwise it may reduce the therapeutic effect. We suggest those sensitive customers who bleed much blood or have serious swell take some antibiotic medicine after treatment.Accesories
Technical parameters
Light Source: ND: YAG LightWavelengths: 1064nm 532nmPulse width: 3.5-10nsOutput power: 600WEnergy: 1500mjSpot diameter: 1-8 mmCooling manner: Wind + water + semiconductorNet Weight: 12.8kgVolume weight: 21KGRepeat frequency: 1 2 3 4 5 6HzPower: 200V/110V 50Hz/60HzWorking Period: Continuously stand-by working for 8 hoursPacking list
1. 1 × Main machine body2. 1 × 532nm tip (mainly used for red, coffee and brown pigment treatment)3. 1 × 1064nm tip (mainly used for blue, black and cyan pigment treatment)4. 1 × Water funnel5. 1 × Package box6. 4 × Key (two for the machine, two for the package box)7. 1 × Foot touch8. 1 × Protective goggle9. 1 × Power line (we stock 110V-240V power version and US.UK.UA.EU plugs for the country all of the world)Effect
Payment terms-Sample Charge: T/T or Western Union-30% deposit before production, 70% balance before shippingPacking and shipping-Standard Export Carton with fully Polyfoam or Pearl Wool-Delivery within 5 to 15 working days upon receiving paymentAfter-Sales-Service-Lifetime with professional engineer support.-Within 1 year, supply spare parts for free if the machine has quality problem.
YAG Laser Tattoo Removal (L006)