Ads by Google
3 Functional Diamond Dermabrasion Machine
BT-508
The Micro-crystal Dermabrasion was designed by Italian Florence's Mattioli at first, until now had over 20 years’ history. This kind of technology only supplies to the dermatology expert and doctor at first uses, but more and more SPA House & Beauty Saloon also gradually uses, it was called the best method of medical beauty. This method successfully has developed in Europe for several years, cures patient thousands of examples, and has obtained the extremely satisfactory effect.
Now we want to introduce the Diamond Dermabrasion, it is a creative improvement of the Micro-crystal Dermabrasion. The Diamond Dermabrasion provided a non-surgical skin refinish procedure, by using sterile diamond heads to abrade or rub off the top skin layer, then Vacuuming out the particles along with any dirt and dead skin back up. This procedure removes skin debris, imperfections, blemishes, wrinkles and unwanted pigmentation on the skin. Moderate usage of Diamond Dermabrasion, accompany with skin products that penetrate through top skin layer that reach the dermis level, helps to replenish natural nutrients, restore cell activity, and promote skin health. The results after Micro Dermabrasion treatment is usually a healthy, glowing, beautiful skin.
Functions Introduction:
1. The Diamond Dermabrasion. (See the preface)
2. The hot & cold treatment function. The cold treatment function is specially designed for claming down the skin after peeling. The skin is sensitive after peeling treatment, so the cold treatment procures is necessary. The hot treatment function is designed for accelerating the absorption of nutrition.
3. Ultrasonic function. Ultrasonic utilizes sonic vibrations; it works one million times per second (1 MHz). The ultrasonic wave could stimulate skin tissue and improve permeability of the membrane to promoted collagen tissue, reduced wrinkle and invisible appeared fine line, also lift the skin result for younger and healthy look. Ultrasonic generate frictional heat which accelerate blood circulation, muscle relaxation, and decompose the cellulite to break down exceed fat. GD-06 Ultrasound with 2 probes provided non-surgical lifting. This machine utilizes sonic vibrations to reduce lines, leaving the skin firm and smooth.
*** Preparation before treatment
1. A consultation included the examination of the skin, a plan for treatment.
2. Operator should wear vinyl gloves and a facemask.
3. On oily or acne skin, a steamer may be used prior to the treatment, or a degreasing lotion may be applied prior to the cleanser.
4. Cleansing the skin with Cleansing gel or water, then wipe off with cotton pad. Allow the skin to dry.
Operating Instruction for Diamond Dermabrasion
1. Push in the movable ring of copper nozzle at the hand piece, and pull out the 6x4 size vacuum hose. Then push in the black plastic ring on the vacuum hose.
2. Put a drop of cream or milk lotion on the vacuum hose nozzle, push in the movable ring and insert in the vacuum hose to the limit.
3. Insert a cotton swab into the Diamond Head, then tight up the Diamond Head on the hand piece. Remove the cotton swab after every treatment.
4. Turn on the power switch.
5. Adjust the Vacuum intensity by Vacuum Regulator according to the following reference table, the intensity displays on Vacuum gauge and check with the client for comfort.
Recommended Vacuum intensity on treatment area
Treatment Area | Normal Skin (inHg) | Sensitive Skin (inHg) |
Face | 12-22 | 8-12 |
Forehead | 12-22 | 10-12 |
Chest | 15-20 | 15-18 |
Nose | 10-15 | 10-14 |
Neck | 18-18 | 10-15 |
Near Eye Area | 8-12 | 8-10 |
Treatment Schedule Table
Treatment | Frequency (days) | Total Visits |
Face Peeling | 6-10 | 3-5 |
Fine Lines | 7-13 | 6-8 |
Neck | 12-14 | 3-5 |
Acne Scars | 7-12 | 8-10 |
Hyperpigmentation | 7-12 | 8-10 |
Treatment Time:5-10 minutes
6 Use the incline area of Hand piece to contact with the skin surface. Proceed with a slow sliding motion. Do not place the hand piece at one spot for too long, doing so will cause harm to the skin.
7. Adjust the crystal flow rate by the Vacuum Regulator slowly from minimum to maximum. For commonly use, do not set the flow rate to maximum unless it is of necessity. This is for better comfort intensity.
8. Gently stretch the skin with thumb and finger and glide the Hand-piece 2 to 3 times over the area being treated. Then cross again in different directions to prevent streaking lines as in the reference picture. Brush strokes or polishing motions may be used in different sites.
DIAGRAM OF SUGGESTED MOVEMENTS
AND AREAS FOR DERMABRASION
*Please follow direction of arrows.
9. After treatment, brush off all remaining dead skin with a soft brush and rinse with damp sponges or damp cool towel.
10. Allow skin to dry then apply desired skin product.
11. To clean the Diamond Head, use toothbrush or cotton swab damped with a little alcohol to wipe off th
e dirty impurity, and then use UV light or high temperature for sterilization.
Operating Instruction for hot & cool treatment
1. Connect the hot & cold plug to the machine; please note the socket is in the “Hot & Cold” Area.
2. Start the machine: To turn on the machine, press the “on” button. And then start the hot & cold treatment function.
3. Please wait 3 minutes, and then you can apply the treatment. For the machine need time to warming up or cool down the treatment probe.
4. Normally one treatment program is about 5 ~10 minutes. Please note that do not stay in one treatment place over time when applying the treatment to avoid any hurt caused by cool head.
5. After treatment, please turn off the machine and then pull out the plug, make clean the probe.
*** Please clean the treatment probe before treatment and after treatment.
Operating Instruction for Ultrasonic function
I. Preparation
(1). Before start the ultrasonic, cleanse the area to be worked. After cleansed, apply suitable lotion and gel to the skin.
(2). Press Power On/Off for Ultrasonic to start the function.
(3). Output intensity display on Intensity window, Press Intensity “up”
and “down” button to set output intensity, output intensity classify into 9 levels, from minimum 0 to maximum 1.8 Watts/cm. Each level is 0.2 Watts/cm. For Facial work, low to mid intensity is recommended. For Body work, mid to maximum intensity is recommended.
II. Face Treatment (Treatment time: 15 minutes)
(1). Connect Face Electrode (big one) into Face Electrode output.
(2). Press Intensity “up” and “down” button to set output intensity to your need.
(3). Press Pulse/Continuing mode to select Pulse or Continuing wave, Pulse/Continuing wave indicator will light on.
(4). Apply the Electrode working on the face.
III. Eye Treatment(Treatment time: 10 minutes)
(1). Connect Eye Electrode (small one) into Electrode output. (Should take out the Face Electrode first)
(2). Press Intensity “up” and “down” button to set output intensity to your need.
(3). Press Pulse/Continuing mode to select Pulse or Continuing wave, Pulse/Continuing wave indicator will light on.
(4). Apply the Electrode working around the Eye area.
*** Important:
1. Clean skin with clear water.
2. Never stop the electrode on the skin in one spot.
3. Always keeps the electrode moving across the skin.
4. Never point the electrode towards chest area.
5. Do not immerse the handle or the machine into water. Doing so
could cause serious injury or death.
6. Store in a dry cool place.
Safety Warning
Do not use on these areas:
1. Sensitive Skin
2. Skin Rash
3. Damaged, Inflamed, or Infected Skin.
4. Surgical scar less than 12 months old.
5. Skin Swollen.
6. The probes can not point to Eye ball.
7. Genitals.
1. Always begin treatment conservatively and observe the effects by the touch and appearance of the skin. A vacuum power that is too high or too big may cause an inflammatory response.
2.Edema and erythema can occur following treatment, but will resolve in few hours.
3.Overly aggressive techniques can cause mild flaking over the next 3-4 days. Epidermis that is treated too aggressively can lead to bleeding in the superficial dermis.
4. Diamond Dermabrasion should not be used on sensitive areas such as eyelids. The eyelids should be closed at all times during the procedure and may be covered with damp cotton pads.
5.The following areas are considered inappropriate for treatment: Skin tumor, moles, birthmark, angioma, lips, eyes, herpes, skin cancer, and liver spots.
3 Functional Diamond Dermabrasion Machine-BT508