Ads by Google
Features of power end:
1.The crankshafts are driven by herringbone gear without tooling withdrawal groove .
2.Crankshafts are made of alloy steel .
3.Crosshead guiding plates are changeable .
4.·Frames are of high strength , supreme rigitidy and light weight for the adoption of welded steel plate parts .
5.The extention rod adopts double dealing structure with excellent sealing effect.
6.The combination of the forced lubrication and splash lubrication applied for the power end.
Stand
The stand is made of welded steel plate with stress relief, which leads to excellent rigidity and high strength. The reinforcing plate structure is applied for stiffness at the crank shaft bearings. Necessary oil reservoir and oil route system are set up inside the stand aiming at cooling and lubrication.
Crankshaft
The crank shafts are alloy steel castings. Gears, connection rods and bearings are separately mounted on the crank shaft. The teeth on the gears are herringbone teeth. The tight fitting is used for the assemble between inner hole of gears and crank shaft together with inserting bolt and locknut for solidification. The big end of rod is installed respectively on three eccentric elbow of the crank shaft by means of the single column roller bearing, while the small end is installed on the cross pin through the double column roller bearing. Both ends of the crank shaft are double column centripetal sphere roller bearing.
Pinion shaft
The pinion shaft are alloy steel forgings assembling with manufactured herringbone teeth gear featured with medium-hardnessed teeth surface. For the convenience of maintenance, the single column centripetal long roller bearing is selected for the internal circle without cover edge. Either end of the shaft can be mounted with belt wheel or sprocket wheel.
Crosshead and extension rod
The materials of the crosshead and the crosshead guiding plate are of outstanding wearing resistance with long service life. By the adoption of upper and lower guiding plates, the concentricity is in a position to be adjusted by employing shims at the lower guiding plate. The crosshead and the intermediate rod are connected by flange bolt, with which rigid connection the concentricity between the rod and the crosshead can be guaranteed. Clamps in light weight are employed for connection between extension rod and piston rod , which are convenient and reliable .
Hydraulic cylinders, valve assembly , liners and pistons are the major components of the fluid end .
Features of hydraulic end:
1.Sealing parts are impacted in rigid with good sealing.
2.Upright hydraulic cylinder obtains excellent suction performance ..
3.L-shaped hydraulic cylinder has the advantage of supreme compression resistance and convenience of replacing valve assembly .
Hydraulic cylinder
Hydraulic cylinder is forged of alloy steel. Three cylinders of one pump are interchangeable with each other. According to customers special requirements, to enhance the anti-corrosion performance, the surface of the hydraulic cylinder is supposed to be processed with chemical plating nickel. Pulsation dampener , shear relief valve and discharge strainer are separately mounted on the outlet.
Valve assembly
The suction valves and discharge valves of RLF mud pump are interchangeable with each other.
Liner
The suction valves and discharge valves of RLF mud pump are interchangeable with each other.
Spray pump
This system is consisted of spray pump, cooling water tank and spray pipelines with the function of the necessary cooling and splashing to liners and pistons to prolong their lifetime.
The splashing pump is the centrifugal pump which can be driven by the belt mounted on the end of input shaft, or can be individually driven by a motor with water as the cooling and lubrication media.
To wash the interface between the pistons and liners back and forth , the fixed spray pipelines are employed which are secured inside the shell.
Lubrication system
he combination of forced lubrication and splashing lubrication is used for the power end. For the purpose of forced lubrication, the gear oil pump located at the oil tank feeds compressed oil to crossheads, extension rods and bearings respectively via the lubrication pipe lines. More ever, the operation situation of the gear oil pump can be observed by the manometer embedded in the after body of mud pumps.
Charging system
Each mud pump can be equipped with one charging pump to avoid air blocking caused by low pressure at the suction inlet. The spray system is driven by a special motor which is installed on the suction pipe assembly. To reduce the total power supply of drilling rigs, driving shaft is employed to drive the spray pump as well.
taper sleeve