Ads by Google
1.cam clutch is a sprag type freewheel supported by bearing, its construction is same as our WOK,good mobility and lower noise than As roller type freewheel.
2.Bearings are required to support axial and radial loads. Lubrication and sealing must also be provided by the installation.
3.Nominal outside dimensions are the same as series 62 ball bearings.
4.A typical arrangement is to install this type alongside a series 62 bearing, within the same location tolerance, as shown on the following page.
Type | Size | spped |
| Weight | Resistance | |||||
torque | ||||||||||
| TKN1) |
| Namax3 | Dr6 | L | e | f |
| TR | |
dH7 | Nm | nimax2) | min-1 |
|
|
|
|
|
| |
|
| min-1 |
|
|
|
|
|
|
| |
WAS(NSS) | 6 | 1.7 | 5,000 | 7,500 | 19 | 6 | 0.6 | 0.3 | 0.01 | 0.18 |
WAS(NSS) | 8 | 3.0 | 4,300 | 6,500 | 24 | 8 | 0.6 | 0.6 | 0.02 | 0.34 |
WAS(NSS) | 10 | 5.4 | 3,500 | 5,200 | 30 | 9 | 0.6 | 0.6 | 0.03 | 0.36 |
WAS(NSS) | 12 | 10 | 3,200 | 4,800 | 32 | 10 | 0.6 | 0.6 | 0.04 | 0.48 |
WAS(NSS) | 15 |
| 2,800 | 4,300 | 35 | 11 | 0.6 | 0.8 | 0.05 | 0.70 |
WAS(NSS) | 20 | 32 | 2,200 | 3,300 | 47 | 14 | 0.8 | 0.8 | 0.12 | 1.4 |
WAS(NSS) | 25 | 45 | 1,900 | 2,900 | 52 | 15 | 0.8 | 1 | 0.14 | 2.4 |
WAS(NSS) | 30 | 72 | 1,600 | 2,400 | 62 | 16 | 0.8 | 1 | 0.22 | 7.8 |
WAS(NSS) | 35 | 114 | 1,300 | 2,000 | 72 | 17 | 0.8 | 1 | 0.31 | 9 |
WAS(NSS) | 40 | 148 | 1,200 | ,1,800 | 80 | 18 | 1.2 | 1 | 0.39 | 10 |
WAS(NSS) | 45 | 174 | 1,000 | 1,600 | 85 | 19 | 1.2 | 1 | 0.44 | 11 |
WAS(NSS) | 50 | 184 | 950 | 1,500 | 90 | 20 | 1.2 | 1 | 0.49 | 13 |
WAS(NSS) | 55 | 246 | 800 | 1,300 | 100 | 21 | 1.2 | 1 | 0.66 | 14 |
WAS(NSS) | 60 | 406 | 700 | 1,100 | 110 | 22 | 1.2 | 1.5 | 0.81 | 26 |
WAS(NSS) | 80 | 850 | 600 | 900 | 140 | 26 | 1.2 | 1.5 | 1.41 | 58 |
cam clutch AS series