Welcome to ECVERY
OBD key prog for bmw
OBD key prog for bmw
Supplier Info
[China Supplier]
Contact Person : Ms. J Taylor
Tel : 0086-755-25897058
Fax : 0086-755-25897058
Product Detail
1.programming of keys in BMW 2005 - 2011 2.For BMW OBD KEY PROG OBD KEY PROG for bmw  is the most newest device for programming of keys in BW 2005 — 2011. Models E60, E65, E66, E70, E71, E81, E82, E87, E88, E90, E91, E92, E93. Where it is established CAS1 CAS2 CAS3 CAS3 +. Including models with engaged algorithm SOPT. Possibilities of the device and difference from other analogs Programming through through OBD all cars including 2010-11. Version 39.2 of version ISSS (together with above versions).   1. Very simple interface.- All becomes automatically.- You shouldn't press additional buttons.- You have inserted into plug OBD, have brought a key to the coil and in 10 seconds the key was programmed. You can't prevent to program to system a key. 2.10 - 15 seconds programming time3.Programs original keys and Chip PCF7936.4.Tests car systems if there there are problems with key programming.5. The device finishes an additional key, but doesn't erase an old key. In total it is possible to write down only 9 keys. But if your new key 10 it will register instead of 1 ro a key.6.  Possibility of remote updating. You can will address to the seller and it to you will update or will repair the device.7.A guarantee of the device 2 years.8.In 2-3 months release updating or the new device for F cepnnn is planned.  Principle of work devices   1. To check up battery charging level. It should be charged not less than 70 %. Otherwise it will lead to failure of the car.2. Before programming the car should is got not less an once by an original key. If the plug of the accumulator has been removed and the original key isn't inserted, but programming won't occur, and the programmer will give out an error.3. To insert the device in OBD a socket4. To wait a threefold sound signal (Beep – Beep – Beep)The signal will repeat, while the key won't be inserted into the aerial / the chip5. To insert a pure key or the chip into the aerial on the device and to hold it there to a three-voice-frequency signal6. After a three-voice-frequency sound signal to insert a key into an ignition lock and to wait for work end7. At successful end of procedure the melody will play8. At occurrence of errors the device will give out a sound error code (see the table of errors)  Attention:Observance of 1 and 2 points of principles of work is very important. Error codes: 12 - CAS Detect Error13 - AIF Lesen Error (CAS Communication Error)14 - SOPT Status Read Error15 - CAS Answer Error17 - Key Init Status Error18 - Key Init Status 2 Error21 - KEY is not accepted. Use another key23 - It's impossible to recover key data from the CAS31 - TAG Write Error32 - TAG Access Error. TAG is not new33 - No TAG. Insert TAG into coil41 - Init status LOCK Error42 - UnInit clear Error43 - CAS in program mode. CAS Reflashing needed52 - CAS Unlock Error53 - Unknown CAS software54 - Authentisierung Error56 - Authentisierung Timeout ErrorSiren - Models NOT SUPPORTED!

OBD key prog for bmw

Ads by Google

About Us | Contact Us | Help | Terms & Conditions
Hot Products: A | B | C | D | E | F | G | H | I | J | K | L | M | N | O | P | Q | R | S | T | U | V | W | X | Y | Z | 0-9
Copyright Notice @ 2008-2013 ECVERY Limited and/or its subsidiaries and licensors. All rights reserved.