Welcome to ECVERY
Vibration Damper
Vibration Damper
Supplier Info
[China Supplier]
Contact Person : Ms. xiaoling shi
Tel : 86-591-87925819
Fax : 86-591-83316700
Product Detail
Aluuminium alloy vibration damper 1.High quality,reasonable price 2.Easy install,fast delivery 3.ISO9001:2008, SGS

Vibration Damper for OPGW

4D series Vibration Damper is a turning fork multi-resonant Vibration Damper founded by Stockblique, and is mainly used in the dispeling and dispersing of the impact energy on the cable caused by the breeze .

Specification:

Collocation:

It is usually used for vibration insulation of OPGW fiber, also include ADSS fiber.

The scheme table for the intallation quantity of OPGW Vibration damper

Cable Dia.(mm)

      Span(m)

d<12

100~300

300~600

600~900

 

12≤d<22

100~350

350~700

700~1000

1000~1200

Q’ty

2

4

6

8

The scheme table for the intallation quantity of ADSS Vibration damper

Cable Dia.(mm)

       Span(m)

d<12

100~250

250~450

450~700

 

12<d<22

100~250

250~500

500~800

800~1000

Q’ty

1

2

4

6

At critical span, usually use more vibration damper for safety.

Choose Model:

When choosing the damper, two factors should be taken into consider, one is damper weight, the other is diameter of the cable. Considering all mainly factors of the OPGW fiber, such as Tensility, wind speed, landform…, and so on. Then make the decision of damper model.

Choose of  weight

Z=(T*M)1/2  academic formula: Z=(T*M)1/2

Meaning: Z means characteristic impedance of fiber, it decides the model of vibration. When Z over 110, used the 4D-30 model. If not bigger than 110, use the 4D-20 model

T---18%-25% rated tensile strength of fiber(KN)  M—the weight unit of fiber kg/km

Choose of Clamp Dia. Range(mm)

The clamp Dia. Range is the Dia.of fiber with doubled Dia.for preformed rods of Tension set(suspension set).If installed the armour rod, the clamp Dia.range will be Dia. of fiber with doubled Dia. of Armour rods.

Installation Hint

Notice:

1,According as calculation,installed the vibration damper with out armour rod, when the location on the inner preformed rod.

2,Setting the armour rod when intall the vibration damper, there will be a distance which less than 50mm between both end of the armour rod and inner preformed rod.

3,If the location on the outer preformed rod, installed the vibration on the inner preformed rod,and the center of vibration should have a distance more than 50mm from the end of outter preformed rods.

4,The direction of the big hammerhead should face the tower when installing the Vibration Damper.

Armour Rod Specification

Packing details:

Factory photo:

About Us / HC Hardware Department:1)Our factory is more than 10,000 square meters big.2)There are 300 employees in our factory including 30 experienced engineers.3)We have formed 6 production lines.4)The capacity of our factory is 200,000 sets per month.5)We have very large markets. our customers are from North America, Sourth America, East Europe, West Europe, Southeast Asia, Middle East, Russia, etc

Vibration Damper

Ads by Google

About Us | Contact Us | Help | Terms & Conditions
Hot Products: A | B | C | D | E | F | G | H | I | J | K | L | M | N | O | P | Q | R | S | T | U | V | W | X | Y | Z | 0-9
Copyright Notice @ 2008-2013 ECVERY Limited and/or its subsidiaries and licensors. All rights reserved.