Ads by Google
Model: AT-ECS-R
Name: 99 Zones LED Display Wireless Service Call System!
Product OverviewAT-ECS-R Wireless Service Call System provides the in time service for clients in restaurant, bar, coffee house, chess room, sauna room and other quiet places. It's reception's great partner to remind them which table or which room need service from LED Display, the system support total 99 rooms display. This will creat a comfortable situation for the clients to enjoy your service and won’t be disturbed by your go around waiters. And it also help you to save cost and increase profits. How it Works: Unique Features:
*DIY installation*99 Rooms' number LED display*Auto play 10s' record voice message*Built-in digit clock*Display the latest 10 calling numbers, calling times or alarming zones
Specifications:Power Supply: DC12V 500mA power adaptor (with built-in rechargeable backup battery) Working Current: 150mA Alarm Current: ≤ 200mA Frequency output: 0.5W RF frequency: 315/433.92MHz
RF signal range: 350 ft
Alarm/Call message: 10s
Transmitting distance: 1,000 meters (open area)
Standard Package Kit include:
*Control Panel×1
*Wireless service call button×6
*Wireless remote control×1
*Wireless door contact×1
*Power adapter×1
OVERVIEW OF EACH ITEM:Wireless LED Display Control Panel:Control panel RenderingThe control panel shows the calling number, and also the correspnding LED on the right side, such as "Call" "Bill" will be lights on. Being this case, you will know which table needs what service from the LED control panel.
Wireless Table Calling Button w 3-press:
This button is be put on each table. it includes 3 press: Call, Bill and Drink.The communication between LED control Panel and this button is wireless.It can insert table number in the black frame.
Keychain Remote Control:Magnetic Contact Detector:
Keychain Remote Control and Magnetic Contact Detector is for the intruder alarm with the LED control Panel.
SIGNAL REPEATER
Signal repeater, which transit wireless sensors` signal up to 500m. We recommand you to buy this item if you install many wireless sensors on different floors!
Operation***Recoding wireless accessories in bulk
Press down the Recoding button for 0.5s and release, it will show A1 on the Hour position, and HH on the minute position, it indicates that the system has entered the recoding status for wireless panic buttons and wireless sensors.
Then trigger the wireless panic button(press any button on the panic button) or wireless sensor, the recoding LED will flash, when you hear a BEEP tone, the recoding is successful. Repeat above operation, you could recode panic buttons in bulk.
If you want to recode the wireless alarm remote control for alarm system, please enter the recoding status, through “page up” and “page down” to make A2 on Hour position and EE on Minute position, it indicates that the control panel enter the alarm remote control recoding status.
Then press down any button on the alarm remote control, the recoding LED flashes, when you hear two BEEP tones, the recoding is successful.
You can exit the recoding status by pressing the Enter button when recoding finished.
After recoding accessories, the Minute position will indicates the numbers of recoded wireless panic buttons.Note:The control panel support totally 99pcs wireless emergency call panic buttons and 10pcs wireless remote controls.
*** Recoding wireless accessories one by onePress down the Recoding button for 0.5s and release, choose enter recoding status of wireless panic buttons or wireless alarm remote control, then press “Reset” button, enter corresponding recoding status. Through “page up” and “page down” to choose which number to be recoded, then trigger the panic button or remote control, the Recoding LED flashed, when hearing BEEP or BEEP BEEP tone, it indicates that recoding is successful.
If this number has been recoded, it will be covered by the new wireless accessories. For the recoded number, the Point LED in number is lighted on, otherwise it is black.***Wireless calling operation
There are two buttons on the wireless panic button, “Call” and “Clear”. If press the “Call” button, the corresponding LED will be lighted on, the siren will give sound “Ding Dong, Ding Dong” or the voice you have recorded.
At the same time, the calling panic button number will be displayed on the Hour position and the calling times will be showed on the Minute position.The first calling time will be 01, and the calling times will be increased after you press down the panic button again. If press “Clear” button, the calling times on the control panel will be cleared out. If press “Call” and “Clear” at the same time, the calling times will be covered by “-”, it indicates that the table has been servered.
If there is no calling or no remote control was pressed within 3 minutes, the system will display time and the latest calling every 5 seconds alternately.
*** Examine or cancel the called numbers
The system will save the latest 10 calling numbers, when the system is under normal clock status, press the “page up” and “page down” button, the Hour and Minute position will show the latest calling numbers and times if your system has been called, the Month and Day position will not shown at this time, the current calling order will be shown in the Week position and save for latest 10 calling order(0-9). Press “page up” to see the previous calling numbers, and press “page down” to see the next calling numbers.
When the control panel is showing the calling number, press the “Reset” button, you will hear BEEP tone, in indicates that the current calling number is cancelled. When the control panel is showing the clock time, press the “Reset” button, you will hear BEEP BEEP two tones, it indicates that all the calling numbers are cancelled.
***Recording alarming voice message
The control panel has an voice pickup which can record 10 seconds of voice message. You can pre-record the alarm message. Press down the Calling button, the control panel will the pre-recorded message to remind you to take proper measures.
*** Recording operation
Press and hold down the Recording button till the Recording LED lights in red, speak out the message (e.g I need service asap etc.) to the MIC. Release the button after recording is completed.
To change the voice message, you only need to repeat the procedures above.
*** Installation of wireless magnetic contact detector
The design of the wireless magnetic contact detector is simple but reliable. When the distance between the emitter and the magnetic is greater than 2cm, RF alarm signals will be sent to the control panel immediately. Use life of the battery is generally between 8 and 12 months, it depends on the opening frequency of the door. The battery shall be replaced by a new one when the undervoltage LED lights in red.
* Clean the surface of the mounting location.* Tear apart the double-side adhesive tape on the front of the magnet and adhere it to the appropriate position.* For steadier mounting, you may remove the plastic cover of the magnet and then drive two screws through the black cover. ArmPressbutton on the wireless remote control to arm the control panel. The siren connected to the control panel will gives off a tone and at the same time the Arm/Disarm LED lights in red on the control panel, the alarming zones are all armed now.
Thereafter, if intruders are detected, the siren will be triggered and alarm to deter intruder.
Application
99 Zones LED Display Wireless Table Waiter Service Call Calling Paging System w 3-press Table Button for Restaurant AT-ECS-R