Ads by Google
Waste plastic recycle line.
| QTY.(Unit) | Description |
| 1 | Lifting Conveyor |
| Working Length: 4500mm | |
| Light Rubber Conveying Belt: 600mm wide | |
| Conveying Speed: 8-15m/min | |
| Motor: 1.1kw | |
| 1 | PC 800 Crusher (with water) |
| Motor: 30kw | |
| Feeding Mouth: 800×560mm | |
| Diameter of rotor: 560mm | |
| Speed of rotor: 580rpm | |
| Rotator: 8pcs | |
| Stator: 4pcs | |
| Material of Knife: W18Cr4V (W- series high speed steel) | |
| There is over-load emergency switch. | |
| The advantage of crushing with water: rough remove sand at the first step. | |
| 1 | Film Friction Washing Machine |
| Motor: 11kw | |
| Screw: 300mm | |
| Diameter of mesh: 3mm | |
| Screw Rotating Speed: 900rpm | |
| Length: 3000mm | |
| This machine has the self dirt-draining function. | |
| The parts contacted the raw material are made of stainless steel. | |
| Working Principle: | |
| With the high speed rotating screw, the sand and soil dirt could be separated. | |
| 1 | Deposit and Float Washing Machine |
| Washing Roller Motor I: 0.55kw | |
| Washing Roller Motor II: 0.55kw | |
| Dirt Collecting Motor: 1.5kw | |
| Dirt Draining Motor: 1.5kw | |
| Driving method: chain with speed reducer | |
| Length: 4600m | |
| Width: 1200m | |
| High: 1760 mm | |
| The parts contacted the raw material are made of stainless steel. | |
| Function: It has the dirt collecting device can drain the dirt deposit at | |
| the bottom of the washing tank. There are one pull forks and three pull drum, | |
| which are rotating slowly, before the material was send to the dewatering | |
| machine the dirty and soil was clean up absolutely. And the dirty and soil was | |
| deposit at the bottom, there is a screw pull them to the discharge port, | |
| then discharge them out | |
| 1 | Screw Feeder |
| Motor power: 1.5kw | |
| Diameter: 250mm | |
| Effective Length: 2500mm | |
| The parts contacted the raw material are made of stainless steel. | |
| Function: Connected with deposit and float flume, when the | |
| Material after Washing, all of material was drop into the screw feeder, and then | |
| with the feeder helical rotating, the material was send to dewatering machine. | |
| 1 | Film Dewatering Machine |
| Motor: 22kw | |
| Rotating Speed: 1270rpm | |
| Diameter of rotor: 700mm | |
| Effective length of rotor: 1300mm | |
| Diameter of mesh: 3mm | |
| The parts contacted the raw material are made of stainless steel | |
| 1 | Pipe Drying System |
| Heating Power: 45kw | |
| Blower Motor: 5.5kw | |
| The pipes are made of stainless steel and diameter is 159mm. | |
| Function: The pipe was made of stainless steel; its shape is “U” flexible, | |
| as the material out of dewatering machine, there is one blowers, and a | |
| heating box, as the heat box generate heat, the blower absorb, so the material | |
| was heat and it’s water content was removal, meanwhile material was | |
| blew to the storage hopper | |
| 1 | Storage Hopper |
| Volume: 0.5m³ | |
| Diameter: 600mm | |
| Height: 1000mm | |
| The parts contacted the raw material are made of stainless steel. | |
PP/PE Waste Plastic Film Crushing Washing &Drying Recycling Line